Onkyo HT-R490 Manual de usuario

ContentsThank you for purchasing the Onkyo AV Receiver.Please read this manual thoroughly before makingconnections and plugging in the unit.Following

10Rear panel facilities• Insert all plugs and connectors securely. Improperconnections can result in noise, poor performance, ordamage to the equipmen

11Rear panel facilities9 z (REMOTE CONTROL)Connect the Onkyo components that have z connectors such as aCD player, and cassette tape deck using the z

12Example of how to connect your equipmentHere is explanation of how to connect the main components to theHT-R490 in the standard manner. There are ma

13Example of how to connect your equipmentConnecting your audio componentsConnecting a CD playerUsing an RCA-type audio connection cable, connect the

14Connecting a satellite tuner or televisionUsing an RCA-type video connection cable, connect the videooutput terminal (composite) on the satellite tu

15Example of how to connect your equipmentVCR(VIDEO 2)TV monitor or Projector(MONITOR OUT)Satellite tuner or TV(VIDEO 1)DVD player or LD player(DVD)An

16Positioning speakersThis unit has two sets of speaker system terminals (forSPEAKERS A and SPEAKERS B).Before connecting the speakers, place them cor

17ANTENNAFM75AMREMOTE CONTROLCENTERSPEAKERSURROUNDSPEAKERSRLININLLRRFRONTCENTERSURRSUBWOOFERRLCOAXIALOUTINABRLFRONT SPEAKERSRLRLVIDEODIGITAL INPUTMONI

18 AM loop antennaConnecting antennasConnecting the AM loop antenna1. Press down the lever.2. Insert the end of thecable into the hole.3. Release the

19Connecting antennasTo TV (or VCR)If the reception condition cannot be improved by adjusting theprovided antenna, install an outdoor antenna and conn

21. Read Instructions – All the safety and operating instructionsshould be read before the appliance is operated.2. Retain Instructions – The safety a

20Connecting the powerTurning this unit ON from an z-connectedcomponentWhen the DVD player, CD player or MD recorder connected withthe HT-R490 through

21Speaker SetupYou need to set up the speaker configuration for the speakersystem connected to the SPEAKERS A terminals (see page 17).Notes:• The spea

22Selecting a sound sourceSelecting a sound source1. Press the desired input selector button.The selected source name appears in the display.If the TA

23Selecting a sound sourceSetting the input signal formatIf the input source is DVD, CD, VIDEO 1, VIDEO 2 or TAPE, youcan specify the input signal for

24Tuning into a radio station1. Press either the AM or FM input selector button.2. Using the TUNING a/s buttons on the frontpanel, tune into the stati

25Selecting a preset radio station1. Press either the AM or FM input selector button.The display should show the currently selected frequency. If itdi

26To enjoy Surround modeThe HT-R490’s surround sound enables you to enjoy the presenceof a movie theater or concert hall in your room.Before using a s

27Input source signal formatAnalog PCM*4Dolby Digital*5dts MULTI CH*6Source software Tape, Record, CD, Audio DVD, Video DVD, LD, CD, LD, Video DVDTune

28To enjoy Surround modeSelecting Onkyo’s surround modes1. Press an input selector button to select thedesired sound source.2. Press the DSP button re

29To record the input source signal you arecurrently watching or listening toRecording of video and/or audio signals can be performed on thecomponents

31. Warranty ClaimYou can find the serial number on the rear panel of this unit. Incase of warranty claim, please report this number.2. Recording Copy

30Using remote controllerCD operationbuttonsTAPE operationbuttonsINPUT SELECTORMODESLEEP DIMMER DISPLAYCD TAPE TUNERD V D VIDEO 1 VIDEO 2SUR MODESW MO

31Using remote controllerControlling an Onkyo DVD playerMake sure that you point the remote controller toward the remotecontrol sensor of the DVD play

32Pre-programming remote controllerINPUT SELECTORMODESLEEP DIMMER DISPLAYCD TAPE TUNERD V D VIDEO 1 VIDEO 2SUR MODESW MODE AUDIO SELTUNERPRESETTV CABL

33CODE LISTBrand TV VCR CABLE DVD SATADMIRAL 01-03 01 ———AIWA — 02 ———AOC 04 ————AUDIO DYNAMIC — 03, 04 ———BELL & HOWELL 01, 02 05 ———BROKSONIC 04

34Troubleshooting guideIf a problem occurs while you are using the remote controller, firsttry to operate the controls on the front panel of the HT-R4

35Troubleshooting guideFM/AM TUNERAM stations cannot be received.• AM loop antenna is not attached.➞ Connect the included AM loop antenna to the AM an

http://www.onkyo.co.jp/HOMEPAGESN 29343046W0103-1Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPANTel: 072-831

4Check that the following accessories are supplied with the HT-R490.AM loop antenna × 1FM indoor antenna × 1Remote controller × 1(RC-446M)FeaturesBatt

5Using the remote controllerPoint the remote controller toward the remote control sensor. TheSTANDBY indicator lights up when the unit receives a sign

6Front panel facilitiesHere is an explanation of the controls and displays on the front panel of the HT-R490.SP SEL TUNING PRESETMEMORYSW MODEDIGITAL

75 DISPLAY buttonEach time you press the DISPLAY button, the screen changes asfollows:When an input source other than FM or AM isselected:Press the DI

8Front panel facilities0Input Selector Buttons (DVD, VIDEO 1, VIDEO 2,FM, AM, TAPE and CD)These buttons are used to select the input source. Pressing

9Remote controllerFor detailed descriptions on the buttons, see “Front panel facilities”on pages 6 through 8.1 SLEEP buttonFor setting the sleep time.