Onkyo HT-R420 Manual de usuario

ContentsThank you for purchasing an Onkyo AV Receiver.Please read this manual thoroughly before makingconnections and plugging in the unit.Following t

10REMOTE CONTROLRLRLINININININCOAXIA LOPTICALININININFRONTSURRCENTERSUBWOOFERVIDEO 2VIDEO 1OUTININOUTOUTOUTDIGITAL INPUTVIDEO 2VIDEO 3VIDEO 1DVD MONIT

11REMOTE CONTROLRLRLINININININCOAXIA LOPTICALININININFRONTSURRCENTERSUBWOOFERVIDEO 2VIDEO 1OUTININOUTOUTOUTDIGITAL INPUTVIDEO 2VIDEO 3VIDEO 1DVD MONIT

12Positioning speakers/Connecting speakersTwo speaker systems can be connected to the Receiver.The speaker system A is to be placed in the main room,

13Positioning speakers/Connecting speakersBefore connecting• Refer also to the instruction manuals of the speakers.• Be sure to connect the positive a

14Connecting the supplied FM and AM indoor antennasConnecting antennasNoteInsert one end of the AM antenna cord to either of the AM antenna connectors

15Connecting an Outdoor FM AntennaIf you cannot achieve good reception with the supplied indoor FMantenna, try a commercially available outdoor FM ant

16Connections for remote control (z)Notes• Connect the plugs securely.• Be sure to connect to the z connectors using the z cable.• For proper operatio

17Enjoying music or videos with the HT-R420Connecting the power1. Connect the power cord to a wall outlet.The HT-R420 enters standby mode.The STANDBY

18Speaker setupFront leftFront rightCenterSurround left Surround rightYou need to set up the speaker configuration for the speaker systemA (see page 1

19Speaker setupSpecifying speaker distancesTo get the best from surround sound, it’s important that the soundfrom each speaker reaches the listener at

2 Important Safety Instructions 1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use th

20SUBWOOFER MODETESTLEVEL 5/∞CH SELAdjusting each speaker’s relative volumebalance — Test toneAdjust each speaker’s relative volume balance so that th

21Switch the source from TAPE to MDYou can set the AV receiver to show “MD” when the TAPE sourceis selected by pressing TAPE on the unit.1 Press TAPE

22Listening to the radioTuning into a radio station1. Press TUNER.The selected band appears in the display. Each time you pressthe button, the band ch

23PRESET 2/3TUNERPRESET/ADJUST ™/£MEMORYFM MODESelecting preset stationsBefore selecting preset stations, you need to preset the radiostations. See “P

24MUTINGSP A/SP BSPEAKERS A/BMuting the sound (remote controller only)Press MUTING.The MUTING indicator flashes in the display during the mutingmode.T

25DISPLAYDIMMERDIMMERSLEEPChanging the displayPress DISPLAY.Each time you press DISPLAY, the screen changes as follows:When an input source other than

26DVDAUDIO SELECTORDVDLEVEL 5/∞AUDIO SELCH SELAdjusting each speaker’s relative volumebalance temporarilyYou can readjust each speaker’s relative volu

27DVD TAPEAUDIO SELECTORDVDAUIO SELDIRECTSURROUNDCH SEL LEVEL 5/∞DIRECTSURROUNDUsing analog multi channel inputThe multi channel input refers to a sys

28The surround sound of the AV Receiver enables you to enjoy thepresence of a movie theater or concert hall in your room.Before using any surround mod

29Selecting the listening modeBefore operating the remote controller, press RCVR/TAPE.Press one of the listening mode buttons.DIRECT button: Set the

3PrecautionsFor U.S. modelsNote to CATV system installer:This reminder is provided to call the CATV system installer’sattention to Section 820-40 of t

30Using the audio adjust functionsBefore operating the remote controller, press RCVR/TAPE.These functions only work with speaker system A.Audio Adjust

31The Audio Adjust functions are explained below.BassWith this function you can boost or cut low-frequency soundsoutput by the front speakers from –12

32REMOTE CONTROLINININININCOAXIALOPTICALININININFRONTSURRCENTERSUBWOOFERVIDEO 2VIDEO 1OUTININOUTOUTOUTDIGITAL INPUTVIDEO 2VIDEO 3VIDEO 1DVD MONITOROUT

33VCRTVCABLE/SATCD/DVDENTUsing the remote controller with your other AVcomponentsEntering the manufacturer’s code (RC-518Monly)If you’re using an Onky

34Using the remote controller with your other AV componentsManufacturer TV VCR DVD Cable SatelliteAIWA 137AKAI 227DENON 302ECHOSTAR 500EMERSON 228FISH

35Using the remote controller with your other AV componentsUsing the RC-518MIf you need to enter the manufacturer’s code for your AVcomponent into the

36Using the remote controller with your other AV components4. VCRoperationbuttons2. VCR£ : Plays side A (the side facingthe front) of tape.7 : Stops p

37Using the remote controller with your other AV components : Power On/Off.1–9, 0 : Use to enter numeric values.CH + : Changes the channelupward.CH

38Causes• The power cord is disconnected.• There is external noise interfering with thecomputer circuits of the AV receiver.• Amplifier protection cir

39When incorrect operation is observed• The HT-R420 contains an internal microcomputer that performs high-level operations. However, on extremely rare

4FeaturesAmplifier Features•5 × 100 W/Channel @ 8Ω, 20–20 kHz, 0.08% THD•WRAT-Wide Range Amplifier Technology• Optimum Gain Volume Circuitry• DTS, Dol

SpecificationsSN 29343627DI0407-5Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPANTel: 072-831-8023 Fax: 072-

5Before Using the HT-R42030˚30˚Approx. 16 feet (5m)Remote control sensorStandby indicatorHT-R420Setting the Voltage Selector(Worldwide model only)The

6Front panelIndex to parts and controlsFor operational instructions, refer to the page indicated in brackets.1 STANDBY/ON button [17]When STANDBY/ON b

7ab c defghiDisplay@ DISPLAY button [25]Each time you press the DISPLAY button, the display changes.# AUDIO SELECTOR button [26, 27]Press to select an

8Index to parts and controlsRear panelFor operational instructions, refer to the page indicated in brackets.1 z REMOTE CONTROL [16]Connect the Onkyo c

9Explanations on this page are for controlling the HT-R420. Tooperate other components, see “Using the remote controller withyour other AV components”